pg.ddx.io pgsql-performance@postgresql.org mailing list archive
help / color / mirror / Atom feedQuad processor options
25+ messages / 14 participants
[nested] [flat]
* Quad processor options
@ 2004-05-11 19:06 Bjoern Metzdorf <bm@turtle-entertainment.de>
0 siblings, 4 replies; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 19:06 UTC (permalink / raw)
To: pgsql-performance; +Cc: Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
Hi,
I am curious if there are any real life production quad processor setups
running postgresql out there. Since postgresql lacks a proper
replication/cluster solution, we have to buy a bigger machine.
Right now we are running on a dual 2.4 Xeon, 3 GB Ram and U160 SCSI
hardware-raid 10.
Has anyone experiences with quad Xeon or quad Opteron setups? I am
looking at the appropriate boards from Tyan, which would be the only
option for us to buy such a beast. The 30k+ setups from Dell etc. don't
fit our budget.
I am thinking of the following:
Quad processor (xeon or opteron)
5 x SCSI 15K RPM for Raid 10 + spare drive
2 x IDE for system
ICP-Vortex battery backed U320 Hardware Raid
4-8 GB Ram
Would be nice to hear from you.
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 19:32 Anjan Dave <adave@vantage.com>
0 siblings, 1 reply; 25+ messages in thread
From: Anjan Dave @ 2004-05-11 19:32 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; pgsql-performance; +Cc: Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
We use XEON Quads (PowerEdge 6650s) and they work nice, provided you configure the postgres properly. Dell is the cheapest quad you can buy i think. You shouldn't be paying 30K unless you are getting high CPU-cache on each processor and tons of memory.
I am actually curious, have you researched/attempted any postgresql clustering solutions? I agree, you can't just keep buying bigger machines.
They have 5 internal drives (4 in RAID 10, 1 spare) on U320, 128MB cache on the PERC controller, 8GB RAM.
Thanks,
Anjan
-----Original Message-----
From: Bjoern Metzdorf [mailto:bm@turtle-entertainment.de]
Sent: Tue 5/11/2004 3:06 PM
To: pgsql-performance@postgresql.org
Cc: Pgsql-Admin (E-mail)
Subject: [PERFORM] Quad processor options
Hi,
I am curious if there are any real life production quad processor setups
running postgresql out there. Since postgresql lacks a proper
replication/cluster solution, we have to buy a bigger machine.
Right now we are running on a dual 2.4 Xeon, 3 GB Ram and U160 SCSI
hardware-raid 10.
Has anyone experiences with quad Xeon or quad Opteron setups? I am
looking at the appropriate boards from Tyan, which would be the only
option for us to buy such a beast. The 30k+ setups from Dell etc. don't
fit our budget.
I am thinking of the following:
Quad processor (xeon or opteron)
5 x SCSI 15K RPM for Raid 10 + spare drive
2 x IDE for system
ICP-Vortex battery backed U320 Hardware Raid
4-8 GB Ram
Would be nice to hear from you.
Regards,
Bjoern
---------------------------(end of broadcast)---------------------------
TIP 4: Don't 'kill -9' the postmaster
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:14 Paul Tuckfield <paul@tuckfield.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
3 siblings, 1 reply; 25+ messages in thread
From: Paul Tuckfield @ 2004-05-11 20:14 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>; pgsql-performance
it's very good to understand specific choke points you're trying to
address by upgrading so you dont get disappointed. Are you truly CPU
constrained, or is it memory footprint or IO thruput that makes you
want to upgrade?
IMO The best way to begin understanding system choke points is vmstat
output.
Would you mind forwarding the output of "vmstat 10 120" under peak load
period? (I'm asusming this is linux or unix variant) a brief
description of what is happening during the vmstat sample would help a
lot too.
> I am curious if there are any real life production quad processor
> setups running postgresql out there. Since postgresql lacks a proper
> replication/cluster solution, we have to buy a bigger machine.
>
> Right now we are running on a dual 2.4 Xeon, 3 GB Ram and U160 SCSI
> hardware-raid 10.
>
> Has anyone experiences with quad Xeon or quad Opteron setups? I am
> looking at the appropriate boards from Tyan, which would be the only
> option for us to buy such a beast. The 30k+ setups from Dell etc.
> don't fit our budget.
>
> I am thinking of the following:
>
> Quad processor (xeon or opteron)
> 5 x SCSI 15K RPM for Raid 10 + spare drive
> 2 x IDE for system
> ICP-Vortex battery backed U320 Hardware Raid
> 4-8 GB Ram
>
> Would be nice to hear from you.
>
> Regards,
> Bjoern
>
> ---------------------------(end of
> broadcast)---------------------------
> TIP 4: Don't 'kill -9' the postmaster
>
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:16 scott.marlowe <scott.marlowe@ihs.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
3 siblings, 1 reply; 25+ messages in thread
From: scott.marlowe @ 2004-05-11 20:16 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: pgsql-performance; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
On Tue, 11 May 2004, Bjoern Metzdorf wrote:
> Hi,
>
> I am curious if there are any real life production quad processor setups
> running postgresql out there. Since postgresql lacks a proper
> replication/cluster solution, we have to buy a bigger machine.
>
> Right now we are running on a dual 2.4 Xeon, 3 GB Ram and U160 SCSI
> hardware-raid 10.
>
> Has anyone experiences with quad Xeon or quad Opteron setups? I am
> looking at the appropriate boards from Tyan, which would be the only
> option for us to buy such a beast. The 30k+ setups from Dell etc. don't
> fit our budget.
>
> I am thinking of the following:
>
> Quad processor (xeon or opteron)
> 5 x SCSI 15K RPM for Raid 10 + spare drive
> 2 x IDE for system
> ICP-Vortex battery backed U320 Hardware Raid
> 4-8 GB Ram
Well, from what I've read elsewhere on the internet, it would seem the
Opterons scale better to 4 CPUs than the basic Xeons do. Of course, the
exception to this is SGI's altix, which uses their own chipset and runs
the itanium with very good memory bandwidth.
But, do you really need more CPU horsepower?
Are you I/O or CPU or memory or memory bandwidth bound? If you're sitting
at 99% idle, and iostat says your drives are only running at some small
percentage of what you know they could, you might be memory or memory
bandwidth limited. Adding two more CPUs will not help with that
situation.
If your I/O is saturated, then the answer may well be a better RAID
array, with many more drives plugged into it. Do you have any spare
drives you can toss on the machine to see if that helps? Sometimes going
from 4 drives in a RAID 1+0 to 6 or 8 or more can give a big boost in
performance.
In short, don't expect 4 CPUs to solve the problem if the problem isn't
really the CPUs being maxed out.
Also, what type of load are you running? Mostly read, mostly written, few
connections handling lots of data, lots of connections each handling a
little data, lots of transactions, etc...
If you are doing lots of writing, make SURE you have a controller that
supports battery backed cache and is configured to write-back, not
write-through.
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:28 Bjoern Metzdorf <bm@turtle-entertainment.de>
parent: Anjan Dave <adave@vantage.com>
0 siblings, 0 replies; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 20:28 UTC (permalink / raw)
To: Anjan Dave <adave@vantage.com>; +Cc: pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
Anjan Dave wrote:
> We use XEON Quads (PowerEdge 6650s) and they work nice,
> provided you configure the postgres properly.
> Dell is the cheapest quad you can buy i think.
> You shouldn't be paying 30K unless you are getting high CPU-cache
> on each processor and tons of memory.
good to hear, I tried to online configure a quad xeon here at dell
germany, but the 6550 is not available for online configuration. at dell
usa it works. I will give them a call tomorrow.
> I am actually curious, have you researched/attempted any
> postgresql clustering solutions?
> I agree, you can't just keep buying bigger machines.
There are many asynchronous, trigger based solutions out there (eRserver
etc..), but what we need is basically a master <-> master setup, which
seems not to be available soon for postgresql.
Our current dual Xeon runs at 60-70% average cpu load, which is really
much. I cannot afford any trigger overhead here. This machine is
responsible for over 30M page impressions per month, 50 page impressums
per second at peak times. The autovacuum daemon is a god sent gift :)
I'm curious how the recently announced mysql cluster will perform,
although it is not an option for us. postgresql has far superior
functionality.
> They have 5 internal drives (4 in RAID 10, 1 spare) on U320,
> 128MB cache on the PERC controller, 8GB RAM.
Could you tell me what you paid approximately for this setup?
How does it perform? It certainly won't be twice as fast a as dual xeon,
but I remember benchmarking a quad P3 xeon some time ago, and it was
disappointingly slow...
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:38 Anjan Dave <adave@vantage.com>
0 siblings, 1 reply; 25+ messages in thread
From: Anjan Dave @ 2004-05-11 20:38 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: pgsql-performance; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
Did you mean to say the trigger-based clustering solution is loading the dual CPUs 60-70% right now?
Performance will not be linear with more processors, but it does help with more processes. We haven't benchmarked it, but we haven't had any problems also so far in terms of performance.
Price would vary with your relation/yearly purchase, etc, but a 6650 with 2.0GHz/1MB cache/8GB Memory, RAID card, drives, etc, should definitely cost you less than 20K USD.
-anjan
-----Original Message-----
From: Bjoern Metzdorf [mailto:bm@turtle-entertainment.de]
Sent: Tue 5/11/2004 4:28 PM
To: Anjan Dave
Cc: pgsql-performance@postgresql.org; Pgsql-Admin (E-mail)
Subject: Re: [PERFORM] Quad processor options
Anjan Dave wrote:
> We use XEON Quads (PowerEdge 6650s) and they work nice,
> provided you configure the postgres properly.
> Dell is the cheapest quad you can buy i think.
> You shouldn't be paying 30K unless you are getting high CPU-cache
> on each processor and tons of memory.
good to hear, I tried to online configure a quad xeon here at dell
germany, but the 6550 is not available for online configuration. at dell
usa it works. I will give them a call tomorrow.
> I am actually curious, have you researched/attempted any
> postgresql clustering solutions?
> I agree, you can't just keep buying bigger machines.
There are many asynchronous, trigger based solutions out there (eRserver
etc..), but what we need is basically a master <-> master setup, which
seems not to be available soon for postgresql.
Our current dual Xeon runs at 60-70% average cpu load, which is really
much. I cannot afford any trigger overhead here. This machine is
responsible for over 30M page impressions per month, 50 page impressums
per second at peak times. The autovacuum daemon is a god sent gift :)
I'm curious how the recently announced mysql cluster will perform,
although it is not an option for us. postgresql has far superior
functionality.
> They have 5 internal drives (4 in RAID 10, 1 spare) on U320,
> 128MB cache on the PERC controller, 8GB RAM.
Could you tell me what you paid approximately for this setup?
How does it perform? It certainly won't be twice as fast a as dual xeon,
but I remember benchmarking a quad P3 xeon some time ago, and it was
disappointingly slow...
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:41 Bjoern Metzdorf <bm@turtle-entertainment.de>
parent: scott.marlowe <scott.marlowe@ihs.com>
0 siblings, 2 replies; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 20:41 UTC (permalink / raw)
To: scott.marlowe <scott.marlowe@ihs.com>; +Cc: pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
scott.marlowe wrote:
> Well, from what I've read elsewhere on the internet, it would seem the
> Opterons scale better to 4 CPUs than the basic Xeons do. Of course, the
> exception to this is SGI's altix, which uses their own chipset and runs
> the itanium with very good memory bandwidth.
This is basically what I read too. But I cannot spent money on a quad
opteron just for testing purposes :)
> But, do you really need more CPU horsepower?
>
> Are you I/O or CPU or memory or memory bandwidth bound? If you're sitting
> at 99% idle, and iostat says your drives are only running at some small
> percentage of what you know they could, you might be memory or memory
> bandwidth limited. Adding two more CPUs will not help with that
> situation.
Right now we have a dual xeon 2.4, 3 GB Ram, Mylex extremeraid
controller, running 2 Compaq BD018122C0, 1 Seagate ST318203LC and 1
Quantum ATLAS_V_18_SCA.
iostat show between 20 and 60 % user avg-cpu. And this is not even peak
time.
I attached a "vmstat 10 120" output for perhaps 60-70% peak load.
> If your I/O is saturated, then the answer may well be a better RAID
> array, with many more drives plugged into it. Do you have any spare
> drives you can toss on the machine to see if that helps? Sometimes going
> from 4 drives in a RAID 1+0 to 6 or 8 or more can give a big boost in
> performance.
Next drives I'll buy will certainly be 15k scsi drives.
> In short, don't expect 4 CPUs to solve the problem if the problem isn't
> really the CPUs being maxed out.
>
> Also, what type of load are you running? Mostly read, mostly written, few
> connections handling lots of data, lots of connections each handling a
> little data, lots of transactions, etc...
In peak times we can get up to 700-800 connections at the same time.
There are quite some updates involved, without having exact numbers I'll
think that we have about 70% selects and 30% updates/inserts.
> If you are doing lots of writing, make SURE you have a controller that
> supports battery backed cache and is configured to write-back, not
> write-through.
Could you recommend a certain controller type? The only battery backed
one that I found on the net is the newest model from icp-vortex.com.
Regards,
Bjoern
Attachments:
vmstat.txt (text/plain, 1.3K) download
~# vmstat 10 120
procs memory swap io system cpu
r b w swpd free buff cache si so bi bo in cs us sy id
1 1 0 24180 10584 32468 2332208 0 1 0 2 1 2 2 0 0
0 2 0 24564 10480 27812 2313528 8 0 7506 574 1199 8674 30 7 63
2 1 0 24692 10060 23636 2259176 0 18 8099 298 2074 6328 25 7 68
2 0 0 24584 18576 21056 2299804 3 6 13208 305 1598 8700 23 6 71
1 21 1 24504 16588 20912 2309468 4 0 1442 1107 754 6874 42 13 45
6 1 0 24632 13148 19992 2319400 0 0 2627 499 1184 9633 37 6 58
5 1 0 24488 10912 19292 2330080 5 0 3404 150 1466 10206 32 6 61
4 1 0 24488 12180 18824 2342280 3 0 2934 40 1052 3866 19 3 78
0 0 0 24420 14776 19412 2347232 6 0 403 216 1123 4702 22 3 74
0 0 0 24548 14408 17380 2321780 4 0 522 715 965 6336 25 5 71
4 0 0 24676 12504 17756 2322988 0 0 564 830 883 7066 31 6 63
0 3 0 24676 14060 18232 2325224 0 0 483 388 1097 3401 21 3 76
0 2 1 24676 13044 18700 2322948 0 0 701 195 1078 5187 23 3 74
2 0 0 24676 21576 18752 2328168 0 0 467 177 1552 3574 18 3 78
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:45 Bjoern Metzdorf <bm@turtle-entertainment.de>
parent: Anjan Dave <adave@vantage.com>
0 siblings, 0 replies; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 20:45 UTC (permalink / raw)
To: Anjan Dave <adave@vantage.com>; +Cc: pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
Anjan Dave wrote:
> Did you mean to say the trigger-based clustering solution
> is loading the dual CPUs 60-70% right now?
No, this is without any triggers involved.
> Performance will not be linear with more processors,
> but it does help with more processes.
> We haven't benchmarked it, but we haven't had any
> problems also so far in terms of performance.
From the amount of processes view, we certainly can saturate a quad
setup :)
> Price would vary with your relation/yearly purchase, etc,
> but a 6650 with 2.0GHz/1MB cache/8GB Memory, RAID card,
> drives, etc, should definitely cost you less than 20K USD.
Which is still very much. Anyone have experience with a self built quad
xeon, using the Tyan Thunder board?
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 20:46 Bjoern Metzdorf <bm@turtle-entertainment.de>
parent: Paul Tuckfield <paul@tuckfield.com>
0 siblings, 1 reply; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 20:46 UTC (permalink / raw)
To: Paul Tuckfield <paul@tuckfield.com>; +Cc: Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>; pgsql-performance
Paul Tuckfield wrote:
> Would you mind forwarding the output of "vmstat 10 120" under peak load
> period? (I'm asusming this is linux or unix variant) a brief
> description of what is happening during the vmstat sample would help a
> lot too.
see my other mail.
We are running Linux, Kernel 2.4. As soon as the next debian version
comes out, I'll happily switch to 2.6 :)
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 21:02 scott.marlowe <scott.marlowe@ihs.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
1 sibling, 2 replies; 25+ messages in thread
From: scott.marlowe @ 2004-05-11 21:02 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: pgsql-performance; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
On Tue, 11 May 2004, Bjoern Metzdorf wrote:
> scott.marlowe wrote:
>
> > Well, from what I've read elsewhere on the internet, it would seem the
> > Opterons scale better to 4 CPUs than the basic Xeons do. Of course, the
> > exception to this is SGI's altix, which uses their own chipset and runs
> > the itanium with very good memory bandwidth.
>
> This is basically what I read too. But I cannot spent money on a quad
> opteron just for testing purposes :)
Wouldn't it be nice to just have a lab full of these things?
> > If your I/O is saturated, then the answer may well be a better RAID
> > array, with many more drives plugged into it. Do you have any spare
> > drives you can toss on the machine to see if that helps? Sometimes going
> > from 4 drives in a RAID 1+0 to 6 or 8 or more can give a big boost in
> > performance.
>
> Next drives I'll buy will certainly be 15k scsi drives.
Better to buy more 10k drives than fewer 15k drives. Other than slightly
faster select times, the 15ks aren't really any faster.
> > In short, don't expect 4 CPUs to solve the problem if the problem isn't
> > really the CPUs being maxed out.
> >
> > Also, what type of load are you running? Mostly read, mostly written, few
> > connections handling lots of data, lots of connections each handling a
> > little data, lots of transactions, etc...
>
> In peak times we can get up to 700-800 connections at the same time.
> There are quite some updates involved, without having exact numbers I'll
> think that we have about 70% selects and 30% updates/inserts.
Wow, a lot of writes then.
> > If you are doing lots of writing, make SURE you have a controller that
> > supports battery backed cache and is configured to write-back, not
> > write-through.
>
> Could you recommend a certain controller type? The only battery backed
> one that I found on the net is the newest model from icp-vortex.com.
Sure, adaptec makes one, so does lsi megaraid. Dell resells both of
these, the PERC3DI and the PERC3DC are adaptec, then lsi in that order, I
believe. We run the lsi megaraid with 64 megs battery backed cache.
Intel also makes one, but I've heard nothing about it.
If you get the LSI megaraid, make sure you're running the latest megaraid
2 driver, not the older, slower 1.18 series. If you are running linux,
look for the dkms packaged version. dkms, (Dynamic Kernel Module System)
automagically compiles and installs source rpms for drivers when you
install them, and configures the machine to use them to boot up. Most
drivers seem to be slowly headed that way in the linux universe, and I
really like the simplicity and power of dkms.
I haven't directly tested anything but the adaptec and the lsi megaraid.
Here at work we've had massive issues trying to get the adaptec cards
configured and installed on, while the megaraid was a snap. Installed RH,
installed the dkms rpm, installed the dkms enabled megaraid driver and
rebooted. Literally, that's all it took.
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 21:11 Bjoern Metzdorf <bm@turtle-entertainment.de>
parent: scott.marlowe <scott.marlowe@ihs.com>
1 sibling, 2 replies; 25+ messages in thread
From: Bjoern Metzdorf @ 2004-05-11 21:11 UTC (permalink / raw)
To: scott.marlowe <scott.marlowe@ihs.com>; +Cc: pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
scott.marlowe wrote:
>>Next drives I'll buy will certainly be 15k scsi drives.
>
> Better to buy more 10k drives than fewer 15k drives. Other than slightly
> faster select times, the 15ks aren't really any faster.
Good to know. I'll remember that.
>>In peak times we can get up to 700-800 connections at the same time.
>>There are quite some updates involved, without having exact numbers I'll
>>think that we have about 70% selects and 30% updates/inserts.
>
> Wow, a lot of writes then.
Yes, it certainly could also be only 15-20% updates/inserts, but this is
also not negligible.
> Sure, adaptec makes one, so does lsi megaraid. Dell resells both of
> these, the PERC3DI and the PERC3DC are adaptec, then lsi in that order, I
> believe. We run the lsi megaraid with 64 megs battery backed cache.
The LSI sounds good.
> Intel also makes one, but I've heard nothing about it.
It could well be the ICP Vortex one, ICP was bought by Intel some time ago..
> I haven't directly tested anything but the adaptec and the lsi megaraid.
> Here at work we've had massive issues trying to get the adaptec cards
> configured and installed on, while the megaraid was a snap. Installed RH,
> installed the dkms rpm, installed the dkms enabled megaraid driver and
> rebooted. Literally, that's all it took.
I didn't hear anything about dkms for debian, so I will be hand-patching
as usual :)
Regards,
Bjoern
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 21:29 scott.marlowe <scott.marlowe@ihs.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
1 sibling, 1 reply; 25+ messages in thread
From: scott.marlowe @ 2004-05-11 21:29 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: pgsql-performance; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
On Tue, 11 May 2004, Bjoern Metzdorf wrote:
> scott.marlowe wrote:
> > Sure, adaptec makes one, so does lsi megaraid. Dell resells both of
> > these, the PERC3DI and the PERC3DC are adaptec, then lsi in that order, I
> > believe. We run the lsi megaraid with 64 megs battery backed cache.
>
> The LSI sounds good.
>
> > Intel also makes one, but I've heard nothing about it.
>
> It could well be the ICP Vortex one, ICP was bought by Intel some time ago..
Also, there are bigger, faster external RAID boxes as well, that make the
internal cards seem puny. They're nice because all you need in your main
box is a good U320 controller to plug into the external RAID array.
That URL I mentioned earlier that had prices has some of the external
boxes listed. No price, not for sale on the web, get out the checkbook
and write a blank check is my guess. I.e. they're not cheap.
The other nice thing about the LSI cards is that you can install >1 and
the act like one big RAID array. i.e. install two cards with a 20 drive
RAID0 then make a RAID1 across them, and if one or the other cards itself
fails, you've still got 100% of your data sitting there. Nice to know you
can survive the complete failure of one half of your chain.
> > I haven't directly tested anything but the adaptec and the lsi megaraid.
> > Here at work we've had massive issues trying to get the adaptec cards
> > configured and installed on, while the megaraid was a snap. Installed RH,
> > installed the dkms rpm, installed the dkms enabled megaraid driver and
> > rebooted. Literally, that's all it took.
>
> I didn't hear anything about dkms for debian, so I will be hand-patching
> as usual :)
Yeah, it seems to be an RPM kinda thing. But, I'm thinking the 2.0
drivers got included in the latest 2.6 kernels, so no biggie. I was
looking around in google, and it definitely appears the 2.x and 1.x
megaraid drivers were merged into "unified" driver in 2.6 kernel.
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-11 21:42 Rob Sell <lists@facnd.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
1 sibling, 0 replies; 25+ messages in thread
From: Rob Sell @ 2004-05-11 21:42 UTC (permalink / raw)
To: pgsql-performance
-----Original Message-----
From: pgsql-performance-owner@postgresql.org
[mailto:pgsql-performance-owner@postgresql.org] On Behalf Of Bjoern Metzdorf
Sent: Tuesday, May 11, 2004 3:11 PM
To: scott.marlowe
Cc: pgsql-performance@postgresql.org; Pgsql-Admin (E-mail)
Subject: Re: [PERFORM] Quad processor options
scott.marlowe wrote:
>>Next drives I'll buy will certainly be 15k scsi drives.
>
> Better to buy more 10k drives than fewer 15k drives. Other than slightly
> faster select times, the 15ks aren't really any faster.
Good to know. I'll remember that.
>>In peak times we can get up to 700-800 connections at the same time.
>>There are quite some updates involved, without having exact numbers I'll
>>think that we have about 70% selects and 30% updates/inserts.
>
> Wow, a lot of writes then.
Yes, it certainly could also be only 15-20% updates/inserts, but this is
also not negligible.
> Sure, adaptec makes one, so does lsi megaraid. Dell resells both of
> these, the PERC3DI and the PERC3DC are adaptec, then lsi in that order, I
> believe. We run the lsi megaraid with 64 megs battery backed cache.
The LSI sounds good.
> Intel also makes one, but I've heard nothing about it.
It could well be the ICP Vortex one, ICP was bought by Intel some time ago..
> I haven't directly tested anything but the adaptec and the lsi megaraid.
> Here at work we've had massive issues trying to get the adaptec cards
> configured and installed on, while the megaraid was a snap. Installed RH,
> installed the dkms rpm, installed the dkms enabled megaraid driver and
> rebooted. Literally, that's all it took.
I didn't hear anything about dkms for debian, so I will be hand-patching
as usual :)
Regards,
Bjoern
-------------------------
Personally I would stay away from anything intel over 2 processors. I have
done some research and if memory serves it something like this. Intel's
architecture makes each processor compete for bandwidth on the bus to the
ram. Amd differs in that each proc has its own bus to the ram.
Don't take this as god's honest fact but just keep it in mind when
considering a Xeon solution, it may be worth your time to do some deeper
research into this. There is some on this here
http://www4.tomshardware.com/cpu/20030422/
Rob
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-11 22:13 Allan Wind <allanwind@lifeintegrity.com>
parent: scott.marlowe <scott.marlowe@ihs.com>
0 siblings, 1 reply; 25+ messages in thread
From: allanwind@lifeintegrity.com @ 2004-05-11 22:13 UTC (permalink / raw)
To: pgsql-performance
On 2004-05-11T15:29:46-0600, scott.marlowe wrote:
> The other nice thing about the LSI cards is that you can install >1 and
> the act like one big RAID array. i.e. install two cards with a 20 drive
> RAID0 then make a RAID1 across them, and if one or the other cards itself
> fails, you've still got 100% of your data sitting there. Nice to know you
> can survive the complete failure of one half of your chain.
... unless that dying controller corrupted your file system. Depending
on your tolerance for risk, you may not want to operate for long with a
file system in an unknown state.
Btw, the Intel and LSI Logic RAID controller cards have suspeciously
similar specificationsi, so I would be surprised if one is an OEM.
/Allan
--
Allan Wind
P.O. Box 2022
Woburn, MA 01888-0022
USA
Attachments:
signature.asc (application/pgp-signature, 188B) download
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-11 22:23 J. Andrew Rogers <jrogers@neopolitan.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
3 siblings, 0 replies; 25+ messages in thread
From: J. Andrew Rogers @ 2004-05-11 22:23 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; pgsql-performance
On Tue, 2004-05-11 at 12:06, Bjoern Metzdorf wrote:
> Has anyone experiences with quad Xeon or quad Opteron setups? I am
> looking at the appropriate boards from Tyan, which would be the only
> option for us to buy such a beast. The 30k+ setups from Dell etc. don't
> fit our budget.
>
> I am thinking of the following:
>
> Quad processor (xeon or opteron)
> 5 x SCSI 15K RPM for Raid 10 + spare drive
> 2 x IDE for system
> ICP-Vortex battery backed U320 Hardware Raid
> 4-8 GB Ram
Just to add my two cents to the fray:
We use dual Opterons around here and prefer them to the Xeons for
database servers. As others have pointed out, the Opteron systems will
scale well to more than two processors unlike the Xeon. I know a couple
people with quad Opterons and it apparently scales very nicely, unlike
quad Xeons which don't give you much more. On some supercomputing
hardware lists I'm on, they seem to be of the opinion that the current
Opteron fabric won't really show saturation until you have 6-8 CPUs
connected to it.
Like the other folks said, skip the 15k drives. Those will only give
you a marginal improvement for an integer factor price increase over 10k
drives. Instead spend your money on a nice RAID controller with a fat
cache and a backup battery, and maybe some extra spindles for your
array. I personally like the LSI MegaRAID 320-2, which I always max out
to 256Mb of cache RAM and the required battery. A maxed out LSI 320-2
should set you back <$1k. Properly configured, you will notice large
improvements in the performance of your disk subsystem, especially if
you have a lot of writing going on.
I would recommend getting the Opterons, and spending the relatively
modest amount of money to get nice RAID controller with a large
write-back cache while sticking with 10k drives.
Depending on precisely how you configure it, this should cost you no
more than $10-12k. We just built a very similar configuration, but with
dual Opterons on an HDAMA motherboard rather than a quad Tyan, and it
cost <$6k inclusive of everything. Add the money for 4 of the 8xx
processors and the Tyan quad motherboard, and the sum comes out to a
very reasonable number for what you are getting.
j. andrew rogers
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-11 22:44 scott.marlowe <scott.marlowe@ihs.com>
parent: Allan Wind <allanwind@lifeintegrity.com>
0 siblings, 0 replies; 25+ messages in thread
From: scott.marlowe @ 2004-05-11 22:44 UTC (permalink / raw)
To: Allan Wind <allanwind@lifeintegrity.com>; +Cc: pgsql-performance
On Tue, 11 May 2004, Allan Wind wrote:
> On 2004-05-11T15:29:46-0600, scott.marlowe wrote:
> > The other nice thing about the LSI cards is that you can install >1 and
> > the act like one big RAID array. i.e. install two cards with a 20 drive
> > RAID0 then make a RAID1 across them, and if one or the other cards itself
> > fails, you've still got 100% of your data sitting there. Nice to know you
> > can survive the complete failure of one half of your chain.
>
> ... unless that dying controller corrupted your file system. Depending
> on your tolerance for risk, you may not want to operate for long with a
> file system in an unknown state.
It would have to be the primary controller for that to happen. The way
the LSI's work is that you disable the BIOS on the 2nd to 4th cards, and
the first card, with the active BIOS acts as the primary controller.
In this case, that means the main card is doing the RAID1 work, then
handing off the data to the subordinate cards.
The subordinate cards do all their own RAID0 work.
mobo ---controller 1--<array1 of disks in RAID0
.....|--controller 2--<array2 of disks in RAID0
and whichever controller fails just kind of disappears.
Note that if it is the master controller, then you'll have to shut down
and enable the BIOS on one of the secondardy (now primary) controllers.
So while it's possible for the master card failing to corrupt the RAID1
set, it's still a more reliable system that with just one card.
But nothing is 100% reliable, sadly.
> Btw, the Intel and LSI Logic RAID controller cards have suspeciously
> similar specificationsi, so I would be surprised if one is an OEM.
Hmmm. I'll take a closer look.
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-11 22:46 Paul Tuckfield <paul@tuckfield.com>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
1 sibling, 2 replies; 25+ messages in thread
From: Paul Tuckfield @ 2004-05-11 22:46 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>; scott.marlowe <scott.marlowe@ihs.com>; pgsql-performance
I'm confused why you say the system is 70% busy: the vmstat output
shows 70% *idle*.
The vmstat you sent shows good things and ambiguous things:
- si and so are zero, so your not paging/swapping. Thats always step
1. you're fine.
- bi and bo (physical IO) shows pretty high numbers for how many disks
you have.
(assuming random IO) so please send an "iostat 10" sampling during
peak.
- note that cpu is only 30% busy. that should mean that adding cpus
will *not* help.
- the "cache" column shows that linux is using 2.3G for cache. (way too
much)
you generally want to give memory to postgres to keep it "close" to
the user,
not leave it unused to be claimed by linux cache (need to leave
*some* for linux tho)
My recommendations:
- I'll bet you have a low value for shared buffers, like 10000. On
your 3G system
you should ramp up the value to at least 1G (125000 8k buffers)
unless something
else runs on the system. It's best to not do things too
drastically, so if Im right and
you sit at 10000 now, try going to 30000 then 60000 then 125000 or
above.
- if the above is off base, then I wonder why we see high runque
numbers in spite
of over 60% idle cpu. Maybe some serialization happening somewhere.
Also depending
on how you've laid out your 4 disk drives, you may see all IOs going
to one drive. the 7M/sec
is on the high side, if that's the case. iostat numbers will reveal
if it's skewed, and if it's random,
tho linux iostat doesn't seem to report response times (sigh)
Response times are the golden
metric when diagnosing IO thruput in OLTP / stripe situation.
On May 11, 2004, at 1:41 PM, Bjoern Metzdorf wrote:
> scott.marlowe wrote:
>
>> Well, from what I've read elsewhere on the internet, it would seem
>> the Opterons scale better to 4 CPUs than the basic Xeons do. Of
>> course, the exception to this is SGI's altix, which uses their own
>> chipset and runs the itanium with very good memory bandwidth.
>
> This is basically what I read too. But I cannot spent money on a quad
> opteron just for testing purposes :)
>
>> But, do you really need more CPU horsepower?
>> Are you I/O or CPU or memory or memory bandwidth bound? If you're
>> sitting at 99% idle, and iostat says your drives are only running at
>> some small percentage of what you know they could, you might be
>> memory or memory bandwidth limited. Adding two more CPUs will not
>> help with that situation.
>
> Right now we have a dual xeon 2.4, 3 GB Ram, Mylex extremeraid
> controller, running 2 Compaq BD018122C0, 1 Seagate ST318203LC and 1
> Quantum ATLAS_V_18_SCA.
>
> iostat show between 20 and 60 % user avg-cpu. And this is not even
> peak time.
>
> I attached a "vmstat 10 120" output for perhaps 60-70% peak load.
>
>> If your I/O is saturated, then the answer may well be a better RAID
>> array, with many more drives plugged into it. Do you have any spare
>> drives you can toss on the machine to see if that helps? Sometimes
>> going from 4 drives in a RAID 1+0 to 6 or 8 or more can give a big
>> boost in performance.
>
> Next drives I'll buy will certainly be 15k scsi drives.
>
>> In short, don't expect 4 CPUs to solve the problem if the problem
>> isn't really the CPUs being maxed out.
>> Also, what type of load are you running? Mostly read, mostly
>> written, few connections handling lots of data, lots of connections
>> each handling a little data, lots of transactions, etc...
>
> In peak times we can get up to 700-800 connections at the same time.
> There are quite some updates involved, without having exact numbers
> I'll think that we have about 70% selects and 30% updates/inserts.
>
>> If you are doing lots of writing, make SURE you have a controller
>> that supports battery backed cache and is configured to write-back,
>> not write-through.
>
> Could you recommend a certain controller type? The only battery backed
> one that I found on the net is the newest model from icp-vortex.com.
>
> Regards,
> Bjoern
> ~# vmstat 10 120
> procs memory swap io system
> cpu
> r b w swpd free buff cache si so bi bo in cs
> us sy id
> 1 1 0 24180 10584 32468 2332208 0 1 0 2 1 2
> 2 0 0
> 0 2 0 24564 10480 27812 2313528 8 0 7506 574 1199 8674
> 30 7 63
> 2 1 0 24692 10060 23636 2259176 0 18 8099 298 2074 6328
> 25 7 68
> 2 0 0 24584 18576 21056 2299804 3 6 13208 305 1598 8700
> 23 6 71
> 1 21 1 24504 16588 20912 2309468 4 0 1442 1107 754 6874
> 42 13 45
> 6 1 0 24632 13148 19992 2319400 0 0 2627 499 1184 9633
> 37 6 58
> 5 1 0 24488 10912 19292 2330080 5 0 3404 150 1466 10206
> 32 6 61
> 4 1 0 24488 12180 18824 2342280 3 0 2934 40 1052 3866
> 19 3 78
> 0 0 0 24420 14776 19412 2347232 6 0 403 216 1123 4702
> 22 3 74
> 0 0 0 24548 14408 17380 2321780 4 0 522 715 965 6336
> 25 5 71
> 4 0 0 24676 12504 17756 2322988 0 0 564 830 883 7066
> 31 6 63
> 0 3 0 24676 14060 18232 2325224 0 0 483 388 1097 3401
> 21 3 76
> 0 2 1 24676 13044 18700 2322948 0 0 701 195 1078 5187
> 23 3 74
> 2 0 0 24676 21576 18752 2328168 0 0 467 177 1552 3574
> 18 3 78
>
> ---------------------------(end of
> broadcast)---------------------------
> TIP 2: you can get off all lists at once with the unregister command
> (send "unregister YourEmailAddressHere" to
> majordomo@postgresql.org)
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-12 04:03 Dennis Bjorklund <db@zigo.dhs.org>
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
3 siblings, 0 replies; 25+ messages in thread
From: Dennis Bjorklund @ 2004-05-12 04:03 UTC (permalink / raw)
To: Bjoern Metzdorf <bm@turtle-entertainment.de>; +Cc: pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
On Tue, 11 May 2004, Bjoern Metzdorf wrote:
> I am curious if there are any real life production quad processor setups
> running postgresql out there. Since postgresql lacks a proper
> replication/cluster solution, we have to buy a bigger machine.
Du you run the latest version of PG? I've read the thread bug have not
seen any information about what pg version. All I've seen was a reference
to debian which might just as well mean that you run pg 7.2 (probably not
but I have to ask).
Some classes of queries run much faster in pg 7.4 then in older versions
so if you are lucky that can help.
--
/Dennis Björklund
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-12 04:58 Grega Bremec <grega.bremec@noviforum.si>
parent: scott.marlowe <scott.marlowe@ihs.com>
1 sibling, 1 reply; 25+ messages in thread
From: Grega Bremec @ 2004-05-12 04:58 UTC (permalink / raw)
To: scott.marlowe <scott.marlowe@ihs.com>; +Cc: Bjoern Metzdorf <bm@turtle-entertainment.de>; pgsql-performance@postgresql.org, "Pgsql-Admin (E-mail)" <pgsql-admin@postgresql.org>
...and on Tue, May 11, 2004 at 03:02:24PM -0600, scott.marlowe used the keyboard:
>
> If you get the LSI megaraid, make sure you're running the latest megaraid
> 2 driver, not the older, slower 1.18 series. If you are running linux,
> look for the dkms packaged version. dkms, (Dynamic Kernel Module System)
> automagically compiles and installs source rpms for drivers when you
> install them, and configures the machine to use them to boot up. Most
> drivers seem to be slowly headed that way in the linux universe, and I
> really like the simplicity and power of dkms.
>
Hi,
Given the fact LSI MegaRAID seems to be a popular solution around here, and
many of you folx use Linux as well, I thought sharing this piece of info
might be of use.
Running v2 megaraid driver on a 2.4 kernel is actually not a good idea _at_
_all_, as it will silently corrupt your data in the event of a disk failure.
Sorry to have to say so, but we tested it (on kernels up to 2.4.25, not sure
about 2.4.26 yet) and it comes out it doesn't do hotswap the way it should.
Somehow the replaced disk drives are not _really_ added to the array, which
continues to work in degraded mode for a while and (even worse than that)
then starts to think the replaced disk is in order without actually having
resynced it, thus beginning to issue writes to non-existant areas of it.
The 2.6 megaraid driver indeed seems to be a merged version of the above
driver and the old one, giving both improved performance and correct
functionality in the event of a hotswap taking place.
Hope this helped,
--
Grega Bremec
Senior Administrator
Noviforum Ltd., Software & Media
http://www.noviforum.si/
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-12 05:34 spied@yandex.ru
parent: Bjoern Metzdorf <bm@turtle-entertainment.de>
0 siblings, 0 replies; 25+ messages in thread
From: spied@yandex.ru @ 2004-05-12 05:34 UTC (permalink / raw)
To: pgsql-performance
BM> see my other mail.
BM> We are running Linux, Kernel 2.4. As soon as the next debian version
BM> comes out, I'll happily switch to 2.6 :)
it's very simple to use 2.6 with testing version, but if you like
woody - you can simple install several packets from testing or
backports.org
if you think about perfomance you must use lastest version of
postgresql server - it can be installed from testing or backports.org
too (but postgresql from testing depend from many other testing
packages).
i think if you upgade existing system you can use backports.org for
nevest packages, if you install new - use testing - it can be used
on production servers today
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-12 08:58 Andrew McMillan <andrew@catalyst.net.nz>
parent: Paul Tuckfield <paul@tuckfield.com>
1 sibling, 0 replies; 25+ messages in thread
From: Andrew McMillan @ 2004-05-12 08:58 UTC (permalink / raw)
To: Paul Tuckfield <paul@tuckfield.com>; +Cc: Bjoern Metzdorf <bm@turtle-entertainment.de>; pgsql-performance
On Tue, 2004-05-11 at 15:46 -0700, Paul Tuckfield wrote:
> - the "cache" column shows that linux is using 2.3G for cache. (way too
> much) you generally want to give memory to postgres to keep it "close" to
> the user, not leave it unused to be claimed by linux cache (need to leave
> *some* for linux tho)
>
> My recommendations:
> - I'll bet you have a low value for shared buffers, like 10000. On
> your 3G system you should ramp up the value to at least 1G (125000 8k buffers)
> unless something else runs on the system. It's best to not do things too
> drastically, so if Im right and you sit at 10000 now, try going to
> 30000 then 60000 then 125000 or above.
Huh?
Doesn't this run counter to almost every piece of PostgreSQL performance
tuning advice given?
I run my own boxes with buffers set to around 10000-20000 and an
effective_cache_size = 375000 (8k pages - around 3G).
That's working well with PostgreSQL 7.4.2 under Debian "woody" (using
Oliver Elphick's backported packages from
http://people.debian.org/~elphick/debian/).
Regards,
Andrew.
-------------------------------------------------------------------------
Andrew @ Catalyst .Net .NZ Ltd, PO Box 11-053, Manners St, Wellington
WEB: http://catalyst.net.nz/ PHYS: Level 2, 150-154 Willis St
DDI: +64(4)916-7201 MOB: +64(21)635-694 OFFICE: +64(4)499-2267
Q: How much does it cost to ride the Unibus?
A: 2 bits.
-------------------------------------------------------------------------
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-12 10:17 Manfred Koizar <mkoi-pg@aon.at>
parent: Paul Tuckfield <paul@tuckfield.com>
1 sibling, 1 reply; 25+ messages in thread
From: Manfred Koizar @ 2004-05-12 10:17 UTC (permalink / raw)
To: Paul Tuckfield <paul@tuckfield.com>; +Cc: Bjoern Metzdorf <bm@turtle-entertainment.de>; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>; scott.marlowe <scott.marlowe@ihs.com>; pgsql-performance
On Tue, 11 May 2004 15:46:25 -0700, Paul Tuckfield <paul@tuckfield.com>
wrote:
>- the "cache" column shows that linux is using 2.3G for cache. (way too
>much)
There is no such thing as "way too much cache".
> you generally want to give memory to postgres to keep it "close" to
>the user,
Yes, but only a moderate amount of memory.
> not leave it unused to be claimed by linux cache
Cache is not unused memory.
>- I'll bet you have a low value for shared buffers, like 10000. On
>your 3G system
> you should ramp up the value to at least 1G (125000 8k buffers)
In most cases this is almost the worst thing you can do. The only thing
even worse would be setting it to 1.5 G.
Postgres is just happy with a moderate shared_buffers setting. We
usually recommend something like 10000. You could try 20000, but don't
increase it beyond that without strong evidence that it helps in your
particular case.
This has been discussed several times here, on -hackers and on -general.
Search the archives for more information.
Servus
Manfred
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-12 10:27 Halford Dace <hal@stowe.co.za>
parent: Manfred Koizar <mkoi-pg@aon.at>
0 siblings, 0 replies; 25+ messages in thread
From: Halford Dace @ 2004-05-12 10:27 UTC (permalink / raw)
To: pgsql-admin@postgresql.org
On 12 May 2004, at 12:17 PM, Manfred Koizar wrote:
> On Tue, 11 May 2004 15:46:25 -0700, Paul Tuckfield <paul@tuckfield.com>
> wrote:
>
>> - I'll bet you have a low value for shared buffers, like 10000. On
>> your 3G system
>> you should ramp up the value to at least 1G (125000 8k buffers)
>
> In most cases this is almost the worst thing you can do. The only
> thing
> even worse would be setting it to 1.5 G.
>
> Postgres is just happy with a moderate shared_buffers setting. We
> usually recommend something like 10000. You could try 20000, but don't
> increase it beyond that without strong evidence that it helps in your
> particular case.
>
> This has been discussed several times here, on -hackers and on
> -general.
> Search the archives for more information.
We have definitely found this to be true here. We have some fairly
complex queries running on a rather underpowered box (beautiful but
steam-driven old Silicon Graphics Challenge DM). We ended up using a
very slight increase to shared buffers, but gaining ENORMOUSLY through
proper optimisation of queries, appropriate indices and the use of
optimizer-bludgeons like "SET ENABLE_SEQSCAN = OFF"
Hal
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: [PERFORM] Quad processor options
@ 2004-05-12 13:44 scott.marlowe <scott.marlowe@ihs.com>
parent: Grega Bremec <grega.bremec@noviforum.si>
0 siblings, 0 replies; 25+ messages in thread
From: scott.marlowe @ 2004-05-12 13:44 UTC (permalink / raw)
To: Grega Bremec <grega.bremec@noviforum.si>; +Cc: Bjoern Metzdorf <bm@turtle-entertainment.de>; pgsql-performance; Pgsql-Admin (E-mail) <pgsql-admin@postgresql.org>
On Wed, 12 May 2004, Grega Bremec wrote:
> ...and on Tue, May 11, 2004 at 03:02:24PM -0600, scott.marlowe used the keyboard:
> >
> > If you get the LSI megaraid, make sure you're running the latest megaraid
> > 2 driver, not the older, slower 1.18 series. If you are running linux,
> > look for the dkms packaged version. dkms, (Dynamic Kernel Module System)
> > automagically compiles and installs source rpms for drivers when you
> > install them, and configures the machine to use them to boot up. Most
> > drivers seem to be slowly headed that way in the linux universe, and I
> > really like the simplicity and power of dkms.
> >
>
> Hi,
>
> Given the fact LSI MegaRAID seems to be a popular solution around here, and
> many of you folx use Linux as well, I thought sharing this piece of info
> might be of use.
>
> Running v2 megaraid driver on a 2.4 kernel is actually not a good idea _at_
> _all_, as it will silently corrupt your data in the event of a disk failure.
>
> Sorry to have to say so, but we tested it (on kernels up to 2.4.25, not sure
> about 2.4.26 yet) and it comes out it doesn't do hotswap the way it should.
>
> Somehow the replaced disk drives are not _really_ added to the array, which
> continues to work in degraded mode for a while and (even worse than that)
> then starts to think the replaced disk is in order without actually having
> resynced it, thus beginning to issue writes to non-existant areas of it.
>
> The 2.6 megaraid driver indeed seems to be a merged version of the above
> driver and the old one, giving both improved performance and correct
> functionality in the event of a hotswap taking place.
This doesn't make any sense to me, since the hot swapping is handled by
the card autonomously. I also tested it with a hot spare and pulled one
drive and it worked fine during our acceptance testing.
However, I've got a hot spare machine I can test on, so I'll try it again
and see if I can make it fail.
when testing it, was the problem present in certain RAID configurations or
only one type or what? I'm curious to try and reproduce this problem,
since I've never heard of it before.
Also, what firmware version were those megaraid cards, ours is fairly
new, as we got it at the beginning of this year, and I'm wondering if it
is a firmware issue.
^ permalink raw reply [nested|flat] 25+ messages in thread
* Re: Quad processor options
@ 2004-05-19 03:38 Marty Scholes <marty@outputservices.com>
0 siblings, 0 replies; 25+ messages in thread
From: Marty Scholes @ 2004-05-19 03:38 UTC (permalink / raw)
To: pgsql-performance
After reading the replies to this, it is clear that this is a
Lintel-centric question, but I will throw in my experience.
> I am curious if there are any real life production
> quad processor setups running postgresql out there.
Yes. We are running a 24/7 operation on a quad CPU Sun V880.
> Since postgresql lacks a proper replication/cluster
> solution, we have to buy a bigger machine.
This was a compelling reason for us to stick with SPARC and avoid
Intel/AMD when picking a DB server. We moved off of an IBM mainframe in
1993 to Sun gear and never looked back. We can upgrade to our heart's
content with minimal disruption and are only on our third box in 11
years with plenty of life left in our current one.
> Right now we are running on a dual 2.4 Xeon, 3 GB Ram
> and U160 SCSI hardware-raid 10.
A couple people mentioned hardware RAID, which I completely agree with.
I prefer an external box with a SCSI or FC connector. There are no
driver issues that way. We boot from our arrays.
The Nexsan ATABoy2 is a nice blend of performance, reliability and cost.
Some of these with 1TB and 2TB of space were recently spotted on ebay
for under $5k. We run a VERY random i/o mix on ours and it will
consistently sustain 15 MB/s in blended read and write i/o, sustaining
well over 1200 io/s. These are IDE drives, so they fail more often than
SCSI, so run RAID1 or RAID5. The cache on these pretty much eliminates
the RAID5 penalties.
> The 30k+ setups from Dell etc. don't fit our budget.
For that kind of money you could get a lower end Sun box (or IBM RS/6000
I would imagine) and give yourself an astounding amount of headroom for
future growth.
Sincerely,
Marty
^ permalink raw reply [nested|flat] 25+ messages in thread
end of thread, other threads:[~2004-05-19 03:38 UTC | newest]
Thread overview: 25+ messages (download: mbox mbox.gz follow: Atom feed)
-- links below jump to the message on this page --
2004-05-11 19:06 Quad processor options Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-11 20:14 ` Paul Tuckfield <paul@tuckfield.com>
2004-05-11 20:46 ` Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-12 05:34 ` spied@yandex.ru
2004-05-11 20:16 ` scott.marlowe <scott.marlowe@ihs.com>
2004-05-11 20:41 ` Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-11 21:02 ` scott.marlowe <scott.marlowe@ihs.com>
2004-05-11 21:11 ` Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-11 21:29 ` scott.marlowe <scott.marlowe@ihs.com>
2004-05-11 22:13 ` Allan Wind <allanwind@lifeintegrity.com>
2004-05-11 22:44 ` scott.marlowe <scott.marlowe@ihs.com>
2004-05-11 21:42 ` Rob Sell <lists@facnd.com>
2004-05-12 04:58 ` Grega Bremec <grega.bremec@noviforum.si>
2004-05-12 13:44 ` scott.marlowe <scott.marlowe@ihs.com>
2004-05-11 22:46 ` Paul Tuckfield <paul@tuckfield.com>
2004-05-12 08:58 ` Andrew McMillan <andrew@catalyst.net.nz>
2004-05-12 10:17 ` Manfred Koizar <mkoi-pg@aon.at>
2004-05-12 10:27 ` Halford Dace <hal@stowe.co.za>
2004-05-11 22:23 ` J. Andrew Rogers <jrogers@neopolitan.com>
2004-05-12 04:03 ` Dennis Bjorklund <db@zigo.dhs.org>
2004-05-11 19:32 Re: [PERFORM] Quad processor options Anjan Dave <adave@vantage.com>
2004-05-11 20:28 ` Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-11 20:38 Re: [PERFORM] Quad processor options Anjan Dave <adave@vantage.com>
2004-05-11 20:45 ` Bjoern Metzdorf <bm@turtle-entertainment.de>
2004-05-19 03:38 Re: Quad processor options Marty Scholes <marty@outputservices.com>
This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox