From: Marc G. Fournier <scrappy@postgresql.org>
To: Aldor <an@mediaroot.de>
Cc: Marc G. Fournier <scrappy@postgresql.org>
Cc: pgsql-admin@postgresql.org
Subject: Re: What is syslog:duration reporting ... ?
Date: Thu, 25 Aug 2005 15:56:36 -0300 (ADT)
Message-ID: <20050825155331.V1044@ganymede.hub.org> (raw)
In-Reply-To: <430E12F1.1080206@mediaroot.de>
References: <20050825152428.T1044@ganymede.hub.org>
<430E12F1.1080206@mediaroot.de>
On Thu, 25 Aug 2005, Aldor wrote:
> As I know EXPLAIN ANALYZE runs the query. I think you are just running the
> query two times. The first time you run the query it will take a long time to
> be processed - after the first run the query planner will remember the best
> way to run the query so your second run runs much faster.
>
> I can reproduce this behavior for some queries under 8.0.1 - so I'm not 100%
> sure if it is the same behavior under 7.4.2.
>
> I'm still wondering why you first query takes about 4107.987 ms - this kind
> of query has usually have to run much much faster.
That would work if I were to get really occasional high values in syslog,
but this is almost a consist thing over a very short period of time:
Aug 25 14:53:32 forgehouse-s1 postgres[23721]: [2-1] LOG: duration: 567.559 ms statement: UPDATE session SET hit_time=now() WHERE md5='7537b74eab488de54d6e0167d1919207';
Aug 25 14:53:32 forgehouse-s1 postgres[23722]: [2-1] LOG: duration: 565.966 ms statement: UPDATE session SET hit_time=now() WHERE md5='d84613009a95296fb511c2cb051ad618';
Aug 25 14:53:33 forgehouse-s1 postgres[23723]: [2-1] LOG: duration: 1192.789 ms statement: UPDATE session SET hit_time=now() WHERE md5='d84613009a95296fb511c2cb051ad618';
Aug 25 14:53:53 forgehouse-s1 postgres[23727]: [2-1] LOG: duration: 12159.162 ms statement: UPDATE session SET hit_time=now() WHERE md5='d84613009a95296fb511c2cb051ad618';
Aug 25 14:53:54 forgehouse-s1 postgres[23728]: [2-1] LOG: duration: 3283.185 ms statement: UPDATE session SET hit_time=now() WHERE md5='7537b74eab488de54d6e0167d1919207';
Aug 25 14:53:57 forgehouse-s1 postgres[23729]: [2-1] LOG: duration: 2116.516 ms statement: UPDATE session SET hit_time=now() WHERE md5='7537b74eab488de54d6e0167d1919207';
And you will notice that the last two are the exact same md5 value ...
> When did you vacuumed the table the last time?
pg_autovacuum is running to keep things up to date, and I just ran a
VACUUM FULL *and* a REINDEX, just to make sure things are clean ...
No matter when I try it, I can't seem to get a value above 10ms for that
query above when I do it from psql ...
>
> Marc G. Fournier wrote:
>>
>> 'k, I've been wracking my brains over this today, and I'm either
>> mis-understanding what is being reported *or* its reporting wrong ...
>>
>> According to syslog:
>>
>> LOG: duration: 4107.987 ms statement: UPDATE session SET hit_time=now()
>> WHERE md5='8b8e7b7ff9b1b2ed5fc60218ced28d00';
>>
>> But, if I do an EXPLAIN ANALYZE:
>>
>> # explain analyze UPDATE session SET hit_time=now() WHERE
>> md5='702c6cb20d5eb254c3feb2991e7e5e31';
>> QUERY PLAN
>>
>> ----------------------------------------------------------------------------------------------------------------------------
>> Index Scan using session_md5_key on "session" (cost=0.00..6.01 rows=1
>> width=93) (actual time=0.060..0.060 rows=0 loops=1)
>> Index Cond: (md5 = '702c6cb20d5eb254c3feb2991e7e5e31'::bpchar)
>> Total runtime: 0.171 ms
>> (3 rows)
>>
>> And it doesn't matter what value I put for md5, I still get <1ms ...
>>
>> I could see some variations, but almost 4000x slower to *really* run the
>> query vs an explain analyze?
>>
>> This is with 7.4.2 ...
>>
>> ----
>> Marc G. Fournier Hub.Org Networking Services (http://www.hub.org)
>> Email: scrappy@hub.org Yahoo!: yscrappy ICQ: 7615664
>>
>> ---------------------------(end of broadcast)---------------------------
>> TIP 2: Don't 'kill -9' the postmaster
>>
>
----
Marc G. Fournier Hub.Org Networking Services (http://www.hub.org)
Email: scrappy@hub.org Yahoo!: yscrappy ICQ: 7615664
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Reply to all the recipients from your mail client; the link fills in
the headers below: reply via email
Some clients, webmail especially, drop In-Reply-To and References from
a link, and the reply then starts a new thread: use the mbox below.
To: pgsql-admin@postgresql.org
Cc: scrappy@postgresql.org, an@mediaroot.de
Subject: Re: What is syslog:duration reporting ... ?
In-Reply-To: <20050825155331.V1044@ganymede.hub.org>
References: <20050825152428.T1044@ganymede.hub.org> <430E12F1.1080206@mediaroot.de> <20050825155331.V1044@ganymede.hub.org>
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox