From: Tim Frank <tfrank@registrar.uoguelph.ca>
To: pgsql-admin@postgresql.org
Cc: brettn@bigpond.com
Subject: Re: PAM authentication
Date: Sat, 01 Feb 2003 12:18:14 -0500
Message-ID: <3E3C0156.2060903@registrar.uoguelph.ca> (raw)
In-Reply-To: <001301c2c8f0$2c54b3d0$0101a8c0@AMD1200>
References: <001301c2c8f0$2c54b3d0$0101a8c0@AMD1200>
Brett,
There was a PAM thread back in early December where we discussed this.
I posted a bunch of PAM testing combinations that did/didn't work. One
of which was trying to use system accounts through "system-auth" which
is really pam_unix.so. This method would not work for me in 7.3.1 no
matter what I tried. I also never found a solution.
Google has the full thread here
http://groups.google.ca/groups?hl=en&lr=&ie=UTF-8&oe=UTF-8&threadm=asqqr7%242mqo%241...
I had a look through some of the authentication source as well, but I
didn't know enough about it to figure out what the problem might be
specifically with pam_unix.so.
Probably not what you wanted to hear, but you aren't the only one.
Tim
Brett Northcott wrote:
> ok - fairly new to postgresql & tring to set up tcp/ip access using pam
> authentication
> using gentoo_linux 1.4_rc2
> postgresql-7.3.1
>
>
> my pg_hba.conf file has the entries
>
> # TYPE DATABASE USER IP-ADDRESS IP-MASK METHOD
>
> local all all trust
> host all all 127.0.0.1 255.255.255.255 trust
> host all all 192.168.1.1 255.255.255.0 pam
> postgresql
>
>
> my /etc/pam.d/postgresql file has the entries
>
> #%PAM-1.0
>
> auth required pam_stack.so service=system-auth
> account required pam_stack.so service=system-auth
>
>
> when i try to connect (locally)....
> # psql test -U brett
> Password: (password entered - i know it is correct)
> psql: FATAL: PAM authentication failed for user "brett"
>
>
> i get the following entries in /var/log/auth.log - and a
> Jan 31 16:31:47 achilles unix_chkpwd[25987]: check pass; user unknown
> Jan 31 16:31:47 achilles postgresql(pam_unix)[25986]: authentication
> failure; logname= uid=70 euid=70 tty= ruser= rhost= user=brett
>
> 'brett' has a system level account.
> i can connect as user 'brett' if pg_hba.conf is set to 'trust', but never
> when pam is involved...
>
> any ideas? i've been mucking around with this for a couple of days & not
> getting very far
>
> regards,
>
> brett
>
>
>
>
> ---------------------------(end of broadcast)---------------------------
> TIP 2: you can get off all lists at once with the unregister command
> (send "unregister YourEmailAddressHere" to majordomo@postgresql.org)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Reply to all the recipients from your mail client; the link fills in
the headers below: reply via email
Some clients, webmail especially, drop In-Reply-To and References from
a link, and the reply then starts a new thread: use the mbox below.
To: pgsql-admin@postgresql.org
Cc: tfrank@registrar.uoguelph.ca, brettn@bigpond.com
Subject: Re: PAM authentication
In-Reply-To: <3E3C0156.2060903@registrar.uoguelph.ca>
References: <001301c2c8f0$2c54b3d0$0101a8c0@AMD1200> <3E3C0156.2060903@registrar.uoguelph.ca>
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox