pg.ddx.io  pgsql-performance@postgresql.org mailing list archive  
help / color / mirror / Atom feed
From: Bruce Momjian <pgman@candle.pha.pa.us>
To: Tom Lane <tgl@sss.pgh.pa.us>
Cc: Mark Kirkwood <markir@paradise.net.nz>
Cc: pgsql-performance@postgresql.org, PostgreSQL-development <pgsql-hackers@postgresql.org>
Subject: Re: [HACKERS] fsync method checking
Date: Thu, 18 Mar 2004 14:55:29 -0500 (EST)
Message-ID: <200403181955.i2IJtT721737@candle.pha.pa.us> (raw)
In-Reply-To: <11459.1079638087@sss.pgh.pa.us>

Tom Lane wrote:
> Bruce Momjian <pgman@candle.pha.pa.us> writes:
> > Tom Lane wrote:
> >> As I recall, that was based on testing on some different platforms.
> 
> > But why perfer O_DSYNC over fdatasync if you don't prefer O_SYNC over
> > fsync?
> 
> It's what tested out as the best bet.  I think we were using pgbench
> as the test platform, which as you know I have doubts about, but at
> least it is testing one actual write/sync pattern Postgres can generate.
> The choice between the open flags and fdatasync/fsync depends a whole
> lot on your writing patterns (how much data you tend to write between
> fsync points), so I don't have a lot of faith in randomly-chosen test
> programs as a guide to what to use for Postgres.

I assume pgbench has so much variance that trying to see fsync changes
in there would be hopeless.

> >> What does that mean?  You can't fsync a closed file.
> 
> > You reopen and fsync.
> 
> Um.  I just looked at that test program, and I think it needs a whole
> lot of work yet.
> 
> * Some of the test cases count open()/close() overhead, some don't.
>   This is bad, especially on platforms like Solaris where open() is
>   notoriously expensive.

The only one I saw that had an extra open() was the fsync after close
test.  I add a do-nothing open/close to the previous test so they are
the same.

> * You really cannot put any faith in measuring a single write,
>   especially on a machine that's not *completely* idle otherwise.
>   I'd feel somewhat comfortable if you wrote, say, 1000 8K blocks and
>   measured the time for that.  (And you have to think about how far

OK, it now measures a loop of 1000.

>   apart the fsyncs are in that sequence; you probably want to repeat the
>   measurement with several different fsync spacings.)  It would also be
>   a good idea to compare writing 1000 successive blocks with rewriting
>   the same block 1000 times --- if the latter does not happen roughly
>   at the disk RPM rate, then we know the drive is lying and all the
>   numbers should be discarded as meaningless.


> 
> * The program is claimed to test whether you can write from one process
>   and fsync from another, but it does no such thing AFAICS.

It really just shows whether the fsync fater the close has similar
timing to the one before the close.  That was the best way I could think
to test it.

> BTW, rather than hard-wiring the test file name, why don't you let it be
> specified on the command line?  That would make it lots easier for
> people to compare the performance of several disk drives, if they have
> 'em.

I have updated the test program in CVS.

New BSD/OS results:

Simple write timing:
        write                    0.034801

Compare fsync times on write() and non-write() descriptor:
(If the times are similar, fsync() can sync data written
 on a different descriptor.)
        write, fsync, close      0.868831
        write, close, fsync      0.717281

Compare one o_sync write to two:
        one 16k o_sync write    10.121422
        two 8k o_sync writes     4.405151

Compare file sync methods with one 8k write:
        (o_dsync unavailable)
        open o_sync, write       1.542213
        (fdatasync unavailable)
        write, fsync,            1.703689

Compare file sync methods with 2 8k writes:
(The fastest should be used for wal_sync_method)
        (o_dsync unavailable)
        open o_sync, write       4.498607
        (fdatasync unavailable)
        write, fsync,            2.473842

-- 
  Bruce Momjian                        |  http://candle.pha.pa.us
  pgman@candle.pha.pa.us               |  (610) 359-1001
  +  If your life is a hard drive,     |  13 Roberts Road
  +  Christ can be your backup.        |  Newtown Square, Pennsylvania 19073



view thread (42+ messages)  latest in thread

Message-ID: <200403181955.i2IJtT721737@candle.pha.pa.us>
Permalink:  ../200403181955.i2IJtT721737@candle.pha.pa.us/
Also on:    postgresql.org/message-id/200403181955.i2IJtT721737@candle.pha.pa.us

 · 

reply

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Reply to all the recipients using the --to and --cc options:
  reply via email

  To: pgsql-performance@postgresql.org
  Cc: pgman@candle.pha.pa.us, tgl@sss.pgh.pa.us, markir@paradise.net.nz, pgsql-hackers@postgresql.org
  Subject: Re: [HACKERS] fsync method checking
  In-Reply-To: <200403181955.i2IJtT721737@candle.pha.pa.us>

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox