From: Brian Wipf <brian@clickspace.com>
To: Ron <rjpeace@earthlink.net>
Cc: pgsql-performance@postgresql.org
Subject: Re: Areca 1260 Performance
Date: Wed, 6 Dec 2006 16:40:55 -0700
Message-ID: <205957AA-B783-4CA7-B620-EFBF86D047EE@clickspace.com> (raw)
In-Reply-To: <E1Gs69E-0002uv-92@elasmtp-scoter.atl.sa.earthlink.net>
References: <BEB285F8-0BD2-4524-BD46-B1D35E7EFBEB@clickspace.com>
<E1Gs3lS-0006i3-0D@elasmtp-banded.atl.sa.earthlink.net>
<D53AD272-BA48-4945-A47D-072E4E2DE1D7@clickspace.com>
<663E7F7B-680B-42C2-BA6A-A237E95CDCEA@clickspace.com>
<E1Gs69E-0002uv-92@elasmtp-scoter.atl.sa.earthlink.net>
I appreciate your suggestions, Ron. And that helps answer my question
on processor selection for our next box; I wasn't sure if the lower
MHz speed of the Kentsfield compared to the Woodcrest but with double
the cores would be better for us overall or not.
On 6-Dec-06, at 4:25 PM, Ron wrote:
> The 1100 series is PCI-X based. The 1200 series is PCI-E x8
> based. Apples and oranges.
>
> I still think Luke Lonergan or Josh Berkus may have some
> interesting ideas regarding possible OS and SW optimizations.
>
> WD1500ADFDs are each good for ~90MBps read and ~60MBps write ASTR.
> That means your 16 HD RAID 10 should be sequentially transferring
> ~720MBps read and ~480MBps write.
> Clearly more HDs will be required to allow a ARC-12xx to attain its
> peak performance.
>
> One thing that occurs to me with your present HW is that your CPU
> utilization numbers are relatively high.
> Since 5160s are clocked about as high as is available, that leaves
> trying CPUs with more cores and trying more CPUs.
>
> You've got basically got 4 HW threads at the moment. If you can,
> evaluate CPUs and mainboards that allow for 8 or 16 HW threads.
> Intel-wise, that's the new Kentfields. AMD-wise, you have lot's of
> 4S mainboard options, but the AMD 4C CPUs won't be available until
> sometime late in 2007.
>
> I've got other ideas, but this list is not the appropriate venue
> for the level of detail required.
>
> Ron Peacetree
>
>
> At 05:30 PM 12/6/2006, Brian Wipf wrote:
>> On 6-Dec-06, at 2:47 PM, Brian Wipf wrote:
>>
>>>> Hmmm. Something is not right. With a 16 HD RAID 10 based on 10K
>>>> rpm HDs, you should be seeing higher absolute performance numbers.
>>>>
>>>> Find out what HW the Areca guys and Tweakers guys used to test the
>>>> 1280s.
>>>> At LW2006, Areca was demonstrating all-in-cache reads and writes
>>>> of ~1600MBps and ~1300MBps respectively along with RAID 0
>>>> Sustained Rates of ~900MBps read, and ~850MBps write.
>>>>
>>>> Luke, I know you've managed to get higher IO rates than this with
>>>> this class of HW. Is there a OS or SW config issue Brian should
>>>> closely investigate?
>>>
>>> I wrote 1280 by a mistake. It's actually a 1260. Sorry about that.
>>> The IOP341 class of cards weren't available when we ordered the
>>> parts for the box, so we had to go with the 1260. The box(es) we
>>> build next month will either have the 1261ML or 1280 depending on
>>> whether we go 16 or 24 disk.
>>>
>>> I noticed Bucky got almost 800 random seeks per second on her 6
>>> disk 10000 RPM SAS drive Dell PowerEdge 2950. The random seek
>>> performance of this box disappointed me the most. Even running 2
>>> concurrent bonnies, the random seek performance only increased from
>>> 644 seeks/sec to 813 seeks/sec. Maybe there is some setting I'm
>>> missing? This card looked pretty impressive on tweakers.net.
>>
>> Areca has some performance numbers in a downloadable PDF for the
>> Areca ARC-1120, which is in the same class as the ARC-1260, except
>> with 8 ports. With all 8 drives in a RAID 0 the card gets the
>> following performance numbers:
>>
>> Card single thread write 20 thread write single
>> thread read 20 thread read
>> ARC-1120 321.26 MB/s 404.76 MB/s 412.55
>> MB/ s 672.45 MB/s
>>
>> My numbers for sequential i/o for the ARC-1260 in a 16 disk RAID 10
>> are slightly better than the ARC-1120 in an 8 disk RAID 0 for a
>> single thread. I guess this means my numbers are reasonable.
>
>
> ---------------------------(end of
> broadcast)---------------------------
> TIP 5: don't forget to increase your free space map settings
>
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Reply to all the recipients from your mail client; the link fills in
the headers below: reply via email
Some clients, webmail especially, drop In-Reply-To and References from
a link, and the reply then starts a new thread: use the mbox below.
To: pgsql-performance@postgresql.org
Cc: brian@clickspace.com, rjpeace@earthlink.net
Subject: Re: Areca 1260 Performance
In-Reply-To: <205957AA-B783-4CA7-B620-EFBF86D047EE@clickspace.com>
References: <BEB285F8-0BD2-4524-BD46-B1D35E7EFBEB@clickspace.com> <E1Gs3lS-0006i3-0D@elasmtp-banded.atl.sa.earthlink.net> <D53AD272-BA48-4945-A47D-072E4E2DE1D7@clickspace.com> <663E7F7B-680B-42C2-BA6A-A237E95CDCEA@clickspace.com> <E1Gs69E-0002uv-92@elasmtp-scoter.atl.sa.earthlink.net> <205957AA-B783-4CA7-B620-EFBF86D047EE@clickspace.com>
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox