From: Tom Lane <tgl@sss.pgh.pa.us>
To: Noah Misch <noah@leadboat.com>
Cc: Daniel Gustafsson <daniel@yesql.se>
Cc: Postgres hackers <pgsql-hackers@lists.postgresql.org>
Cc: Craig Ringer <craig.ringer@enterprisedb.com>
Subject: Re: pgsql: Adjust configure to insist on Perl version >= 5.8.3.
Date: Sat, 09 Oct 2021 15:44:17 -0400
Message-ID: <245162.1633808657@sss.pgh.pa.us> (raw)
In-Reply-To: <20211009192333.GA450252@rfd.leadboat.com>
References: <150C7533-8A64-4829-ABEA-50F0D49FC598@yesql.se>
<161525.1633632402@sss.pgh.pa.us>
<162421.1633633360@sss.pgh.pa.us>
<12C3DA75-ACE1-486B-A432-9E23C68E7D34@yesql.se>
<173186.1633635888@sss.pgh.pa.us>
<20211008025659.GA398563@rfd.leadboat.com>
<197091.1633664351@sss.pgh.pa.us>
<20211008042454.GB398563@rfd.leadboat.com>
<03177128-BE87-4520-90D1-D5FA16B79EB6@yesql.se>
<234637.1633709021@sss.pgh.pa.us>
<20211009192333.GA450252@rfd.leadboat.com>
Noah Misch <noah@leadboat.com> writes:
> On Fri, Oct 08, 2021 at 12:03:41PM -0400, Tom Lane wrote:
>> You're not going to get far with "improving the recipe", because it's
>> just not possible. To check this, I installed perlbrew on a Fedora 34
> Your test result is evidence that "cpanm install Test::More@0.87" is the wrong
> shell command, but it's quite a leap to "just not possible". Surely there
> exist other shell commands that install
> http://backpan.perl.org/modules/by-authors/id/M/MS/MSCHWERN/Test-Simple-0.87_03.tar.gz.
> (Perhaps none of us will care enough to identify them, but they exist.)
Oh, I never heard of backpan before. Now I'm tempted to see how far
I can downgrade prairiedog before it breaks ;-). However, I agree
that most people won't care about that, and probably shouldn't need to.
> By the way, I suspect 93fb39e introduced a regression in the recipe. (I
> haven't tested, though.) Before commit 93fb39e, "cpanm install IPC::Run"
> would update Test::More. As of 5.8.3, the core version of Test::More is new
> enough for IPC::Run but not new enough for PostgreSQL. I recommend adding
> "cpanm install Test::More" to restore the pre-93fb39e functionality.
Good point. So how about like the attached?
regards, tom lane
Attachments:improve-test-perl-README-2.patch (text/x-diff, 1.7K) downloaddiff --git a/src/test/perl/README b/src/test/perl/READMEindex bfc7cdcfa3..ab986f14bc 100644--- a/src/test/perl/README+++ b/src/test/perl/README@@ -70,20 +70,33 @@ perldoc for the test modules, e.g.:
perldoc src/test/perl/PostgresNode.pm
-Required Perl--------------+Portability+-----------++Avoid using any bleeding-edge Perl features. We have buildfarm animals+running Perl versions as old as 5.8.3, so your tests will be expected+to pass on that.-Tests must run on perl 5.8.3 and newer. perlbrew is a good way to obtain such-a Perl; see http://perlbrew.pl .+Also, do not use any non-core Perl modules except IPC::Run. Or, if you+must do so for a particular test, arrange to skip the test when the needed+module isn't present. If unsure, you can consult Module::CoreList to find+out whether a given module is part of the Perl core, and which module+versions shipped with which Perl releases.-Just install and+One way to test for compatibility with old Perl versions is to use+perlbrew; see http://perlbrew.pl . After installing that, do
perlbrew --force install 5.8.3
perlbrew use 5.8.3
perlbrew install-cpanm
+ cpanm install Test::More
cpanm install IPC::Run
-then re-run configure to ensure the correct Perl is used when running-tests. To verify that the right Perl was found:+Then re-run Postgres' configure to ensure the correct Perl is used when+running tests. To verify that the right Perl was found:
grep ^PERL= config.log
++(Note: this recipe does not create a perfect reproduction of a+back-in-the-day Perl installation, because it will update Test::More+and IPC::Run to current versions. In most cases that won't matter.)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Reply to all the recipients from your mail client; the link fills in
the headers below: reply via email
Some clients, webmail especially, drop In-Reply-To and References from
a link, and the reply then starts a new thread: use the mbox below.
To: pgsql-committers@postgresql.org
Cc: tgl@sss.pgh.pa.us, noah@leadboat.com, daniel@yesql.se, pgsql-hackers@lists.postgresql.org, craig.ringer@enterprisedb.com
Subject: Re: pgsql: Adjust configure to insist on Perl version >= 5.8.3.
In-Reply-To: <245162.1633808657@sss.pgh.pa.us>
References: <150C7533-8A64-4829-ABEA-50F0D49FC598@yesql.se> <161525.1633632402@sss.pgh.pa.us> <162421.1633633360@sss.pgh.pa.us> <12C3DA75-ACE1-486B-A432-9E23C68E7D34@yesql.se> <173186.1633635888@sss.pgh.pa.us> <20211008025659.GA398563@rfd.leadboat.com> <197091.1633664351@sss.pgh.pa.us> <20211008042454.GB398563@rfd.leadboat.com> <03177128-BE87-4520-90D1-D5FA16B79EB6@yesql.se> <234637.1633709021@sss.pgh.pa.us> <20211009192333.GA450252@rfd.leadboat.com> <245162.1633808657@sss.pgh.pa.us>
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
This inbox is served by DDX for PostgreSQL; see mirroring instructions
for how to clone and mirror all data and code used for this inbox